Split System Installation Glen Waverley, Room by Room

Peak Air Conditioning Glen Waverley handles split system installation Glen Waverley wide, sizing each indoor unit to the room it serves rather than fitting one size everywhere. A bedroom, a study and an open-plan living area all need different capacities, so the installer measures each space before recommending a unit between 2.5 kW and 8 kW. The quote covers the indoor head, the outdoor unit, the refrigerant pipe run, the condensate drain and any new power circuit, and the work is carried out under an ARC refrigerant handling licence. Single splits and dual-head or three-head multi systems are installed in older homes on large blocks, new townhouses and apartments near Kingsway. Reverse cycle models heat in winter as well as cooling in summer. Call for a fixed written quote after an inspection, with bookings taken from 6am to 10pm, seven days.

GET A FREE QUOTE

Licensed Air Conditioning Glen Waverley Technicians for Split System Installation

Air conditioning work in Glen Waverley draws on three licensed trades: refrigerant handling, electrical connection and, for gas heating, gasfitting. Peak Air Conditioning Glen Waverley is based in the suburb, so a job off Kingsway, in a Legend Park Estate house or in a new townhouse near the station is a local trip rather than a drive across Melbourne. Two things decide whether a new or repaired system performs: who handles the work, and how the system is sized for the rooms it serves.

Peak Air Conditioning Glen Waverley

Split System Installation Glen Waverley: Single-Room and Multi-Room Units

Split system installation in Glen Waverley falls into two layouts: one indoor unit paired with one outdoor unit for a single room, or a multi-room layout for a group of rooms. A multi-room job either gives each room its own single split and outdoor unit, or runs several indoor heads from one shared outdoor unit, and the choice depends on how many rooms need conditioning and how much wall and yard space is free outside.

A split system reverse cycle air conditioner heats and cools from the same indoor and outdoor unit, so one reverse cycle air conditioning installation covers both winter and summer. Cooling-only and reverse cycle models are both available, and the choice is made at the quote; the reverse cycle air conditioning page explains how that heating works against gas. The style of indoor unit is then chosen to suit the space and the wall it hangs on.

Hi-Wall Split Systems for Bedrooms and Studies

The hi-wall unit is the most common split system indoor head. It mounts high on a wall, usually above a window or door, and pushes air across the ceiling so it mixes through the room instead of landing on the bed or desk. In a bedroom or study the main placement question is the pipe route: an external wall is usually best, because the refrigerant pipes and drain can pass straight through to the outdoor unit in a short, tidy run.

Larger Split Systems for Open-Plan Living Areas

Open-plan kitchen, dining and living spaces are common in renovated Glen Waverley homes and in the townhouses replacing older houses on subdivided blocks. These spaces need a larger split than a bedroom, sized from the combined floor area, ceiling height and glazing, and mounted on the wall that lets air travel down the length of the room. The installer checks how far each model's airflow reaches, because a unit on a short end wall can leave the far side of a long room under-conditioned even when the capacity is right.

Slimline and Designer Indoor Units

Where a standard white head would look out of place, slimline and designer indoor units offer a thinner profile, a flatter front panel or a coloured finish. Several brands also make floor console units that sit low on the wall, which suits rooms with high windows or no clear wall space near the ceiling. These styles usually cost more than a standard hi-wall of the same capacity and come in fewer sizes, so the installer confirms the model is made in the capacity the room needs before it goes on the quote.

Forest Hill Emergency Air Conditioning Repair
Clayton Emergency Air Conditioning Repair

Peak Air Conditioning Glen Waverley

How a Split System Is Installed

A split system installation follows the same sequence on every job. Each step affects how quietly and efficiently the system runs for the rest of its life, so none of them is skipped.

Matching 2.5kW to 8kW Capacity to the Room

Before any drilling, the installer measures the room and records the floor area, ceiling height, window size and direction, insulation and how the room is used. Those details set the heat load, which decides whether the room needs a small 2.5 kW unit, a 3.5 kW unit, or a larger 5 kW, 7 kW or 8 kW unit. An undersized unit runs flat out and still struggles on the hottest days, while an oversized one cycles on and off, feels uneven and wastes power.

Wall Bracket, Core Hole and Pipe Cover

The indoor unit hangs on a steel wall bracket fixed level into studs or masonry, so the head sits square and drains in the right direction. A core drill then cuts a round hole through the wall behind the unit for the refrigerant pipes, the power and communication cable and the drain line. Outside, the pipes run inside a pipe cover, a moulded duct that shields the insulation from sun damage and gives the wall a neat finish instead of exposed lagging.

Condensate Drain and Outdoor Unit Mounting

In cooling mode the indoor unit pulls moisture out of the air, and that water leaves through a condensate drain that must fall steadily to a garden bed or stormwater point. Where gravity will not work, a small condensate pump is fitted. The outdoor unit sits on a level slab, anti-vibration feet or a wall bracket, with clear space around it for airflow and servicing, and away from bedroom windows where its fan noise would carry at night.

Leak Test, Commissioning and Remote Setup

Once the pipes are joined, the system is pressure tested with nitrogen, then vacuumed to remove air and moisture before the refrigerant is released into the lines. The installer runs the unit in cooling and heating, checks pressures, airflow and drainage, and listens for vibration at the outdoor unit. The job ends with a walk-through of the remote or wi-fi app, covering modes, timers, filter cleaning and when to book an air conditioning service.

Peak Air Conditioning Glen Waverley

Why Choose Peak Air Conditioning Glen Waverley

Peak Air Conditioning Glen Waverley keeps split system installation simple: licensed work, a price in writing and booking hours that fit around work and school runs.

Licensed Refrigerant Handlers, Not a DIY Install

Australian rules require any person who installs, commissions or services refrigeration and air conditioning equipment to hold a refrigerant handling licence, issued through ARCtick. That makes a split system a job for a licensed installer rather than a weekend project, even when the unit is bought from a retailer as a boxed kit. A DIY connection risks refrigerant leaks and can put the manufacturer warranty at risk, because that warranty applies when the system is installed to the manufacturer's requirements.

Fixed Written Quote for Each Room

After the inspection, the quote prices each room separately: the unit model and capacity, the pipe run, the outdoor unit position, any bracket or roof mount, the electrical work and removal of an old unit. A household can then fit the main living area now and add bedrooms later, knowing the cost of each room in advance. The written price stays the same unless the scope of the work changes, so there is no surprise on the day.

Open 6am to 10pm, Seven Days

Phones are answered from 6am to 10pm, seven days a week, so an inspection can be booked before work or in the evening. Installation dates are offered across the week, including weekends, and same-day inspections are arranged where possible. That suits households who commute into the city on the Glen Waverley line and would rather not lose a weekday waiting at home for a tradesperson.

Burwood East Emergency Air Conditioning Repair
Clayton Emergency Air Conditioning Repair

Peak Air Conditioning Glen Waverley

What Split System Installation Costs in Glen Waverley

Melbourne cost guides put a standard back-to-back install of a 3.5 kW split at around $2,100 to $2,600 (Climate Control Solutions installation cost calculator, reviewed July 2026). These figures are indicative only, not a set price, and the final cost depends on the four factors below. A written quote follows the inspection.

What a Standard Back-to-Back Install Includes

A back-to-back install places the outdoor unit directly on the other side of the wall from the indoor unit, so the pipe run is short and the work is straightforward. It normally covers the wall bracket, the core hole, a short pipe and cable run, the drain, the outdoor unit on a slab or bracket, and commissioning. Where the household already owns the unit, the whatsthedamage.com.au Melbourne guide puts install-only work at around $735 to $1,575 (November 2026).

Unit Capacity and Brand

The unit is the largest part of the bill, and the price climbs with capacity. The same Climate Control Solutions calculator lists indicative installed prices of about $1,900 to $2,500 for 2.5 kW, $2,700 to $3,500 for 5.0 kW and $3,700 to $4,700 for 8.0 kW. Within each size, premium models with wi-fi, quieter fans or higher star ratings cost more than the entry-level range from the same brand.

Extra Pipe Length, Second Storey and Roof Mounts

Costs rise when the outdoor unit cannot sit directly behind the indoor unit. A longer pipe run means more copper, insulation and pipe cover, and an upstairs bedroom may need the pipes run down the outside wall or through the roof space. Roof mounts and high brackets add access equipment and labour. Replacing an old split adds removal: about $250 per unit on the Climate Control Solutions calculator, or $105 to $370 for removal and disposal in the whatsthedamage.com.au guide.

Dedicated Power Circuit From the Switchboard

Many splits need a dedicated circuit run from the switchboard, with an isolator beside the outdoor unit. That electrical work must be done by a licensed electrician, and the Climate Control Solutions calculator suggests allowing roughly $450 extra where a new circuit is needed. Switchboards in some of the 1950s to 1970s homes across Glen Waverley need work before another circuit can be added, which is checked at the inspection and priced as a separate line.

Peak Air Conditioning Glen Waverley

Split System Versus Portable and Window Air Conditioners

Portable and window air conditioners cost less to buy and need no installer, which makes them tempting for one hot room. The differences show up once they are running through a full summer and winter.

Cooling Output and Running Cost

A portable unit keeps its compressor inside the room and pushes hot air out through a flexible hose in a window gap, so part of its effort goes into fighting the heat it creates. A split system puts the compressor outside and uses an inverter to slow down once the room reaches temperature, which usually means less power for the same comfort. Splits also seal through the wall, so there is no open window gap letting hot air back in while the unit runs.

Noise Inside the Room

Because a portable or window unit holds the compressor and fan in one box, all of its noise stays in the room, which is hard to ignore in a bedroom at night. A split system leaves only the indoor fan inside, and most indoor heads have a quiet or night mode for sleeping. The outdoor unit's noise stays outside, which is why its position away from bedroom windows, including a neighbour's, is settled at the planning stage.

Apartments, Townhouses and Owners Corporation Approval

Glen Waverley now has many townhouses on subdivided blocks and apartment buildings around Kingsway and The Glen, and most are managed by an owners corporation. A split usually means drilling an external wall and placing an outdoor unit on a balcony, roof or common area, and those changes often need the owners corporation's written approval first. A portable unit avoids that step, which is its main advantage in a strata building. Where approval is likely, the installer can supply unit dimensions and a proposed layout to support the application.

Burwood East Emergency Air Conditioning Repair
Clayton Emergency Air Conditioning Repair

Peak Air Conditioning Glen Waverley

Multi-Head Split Systems for Several Rooms

A multi-head system, also called a multi-split, connects two or more indoor units to one outdoor unit. It suits homes where several rooms need heating and cooling but the space outside for outdoor units is limited.

Dual-Head and Three-Head Setups

A dual-head system is the most common choice, often pairing the main living area with the main bedroom, while a three-head setup adds a second bedroom or a study. Each indoor unit can be a different size and style, and each has its own remote, so one room can run while another is switched off. The whatsthedamage.com.au Melbourne guide puts a supplied and installed two-head system at around $4,200 to $7,900, with a typical job near $5,800 (November 2026).

One Outdoor Unit Versus Several Single Splits

Separate single splits give each room its own outdoor unit, so a fault in one leaves the others running, and each can be replaced on its own. A multi-head saves wall and yard space and can cost less: Climate Control Solutions estimates two separate 3.5 kW splits at about $4,600 to $5,800 installed, against about $4,000 to $5,200 for a two-head multi-head. The trade-off is that if the shared outdoor unit fails, every connected room loses heating and cooling until it is repaired.

Pipe Length Limits and Running Rooms at Once

Every multi-head outdoor unit has a maximum pipe length for each indoor unit and for the whole system, plus a limit on the height difference between units, all set in the manufacturer's installation manual. Rooms at opposite ends of a long single-storey home can exceed those limits, which is when separate splits or ducted air conditioning make more sense. Most multi-head systems also run every head in the same mode, so one room cannot cool while another heats, and all heads running at once share the outdoor unit's total capacity.

Peak Air Conditioning Glen Waverley

Choosing the Best Split System Air Conditioner for Each Room

Once the heat load check has set the capacity, the best split system for a room comes down to features, efficiency and brand. Each room puts different demands on the unit, so the right model for a bedroom is rarely the right one for the lounge.

Best Split System for a Bedroom

In a bedroom, the indoor unit's noise level matters most. Spec sheets list a sound level in decibels at the lowest fan speed, and a lower figure means a quieter night. Useful bedroom features include a sleep or night mode that eases the temperature overnight, a display that can be dimmed or switched off, and a timer or wi-fi app to warm the room before bed. The capacity still comes from the heat load check, since a sunny upstairs bedroom can need more than a shaded one of the same size.

Best Split System for a Large Room

A large living area runs its split for longer than any other room, so efficiency has the biggest effect on the power bill there. The energy rating label shows how much power the unit uses, and a higher star rating at the same capacity costs less to run year after year. It also pays to compare rated heating capacity and airflow between models, because two units of the same kW size can move different volumes of air, and one may suit a long open room better.

Best Split System for Heating Through a Melbourne Winter

A split system reverse cycle air conditioner heats as well as cools, drawing heat from the outside air even on cold mornings. Heating output can fall as the outdoor temperature drops, so the installer checks the heating capacity, not only the cooling figure, and looks at the cold-zone star rating on the label. For homes still heated by an old gas space heater, the Victorian Energy Upgrades program lists a discount of up to $1,610 and bill savings of up to $460 a year for replacing it with an efficient reverse cycle air conditioner, subject to its eligibility rules.

Daikin, Mitsubishi Electric and Panasonic Split Systems Compared

Daikin, Mitsubishi Electric and Panasonic all sell inverter reverse cycle split systems across the common household sizes, with standard hi-wall models and premium ranges. The useful comparison is model by model rather than brand by brand: star ratings, the quietest indoor sound level, wi-fi control, filter type and the warranty terms each manufacturer sets for that model. Fujitsu models can be quoted on the same basis. The installer lays these details side by side in the written quote, so the choice rests on the spec sheets for the room rather than a showroom pitch.

Burwood East Emergency Air Conditioning Repair

TESTIMONIALS

What Our Split System Installation Customers Say About Us

The Process

3 Step Process For Your Split System Installation Needs

Booking

Call or send a booking request between 6am and 10pm, seven days, describing the system, the rooms involved and the fault or job needed.

Written Quote

The technician inspects the house or the fault, checks sizing, access and wiring, then gives a written quote before any work or part is ordered.

Job Completed

Licensed technicians install or repair the system, test it in heating and cooling modes, explain the controls and leave the required compliance certificates.

FREQUENTLY ASKED QUESTIONS

Split System Installation In

Everything you need to know about our Split System Installation In

How much does it cost to install a split system air conditioner in Melbourne?

The whatsthedamage.com.au Melbourne guide puts a supplied and installed split at around $1,250 to $2,625 for a 2.5 kW unit and $1,475 to $2,950 for 3.5 kW, rising to $2,300 to $4,725 for 7 kW (November 2026). Install-only work on a unit the household already owns sits at around $735 to $1,575 in the same guide. Long pipe runs, a second storey, a roof mount or a new power circuit add to that. These are indicative figures, and the actual price comes in a written quote after an inspection.

Is it easy to install a split system?

Mounting the indoor unit looks simple, but joining the refrigerant pipes, pressure testing, vacuuming the lines and releasing the refrigerant is licensed work in Australia. Anyone who installs or commissions a split system must hold an ARC refrigerant handling licence, and the power circuit must be connected by a licensed electrician. A poor install can leak refrigerant, run water back into the wall or overload a circuit. For a licensed installer, a standard back-to-back job is routine work.

How long does a split system installation take?

A standard back-to-back installation is usually finished within a day. Jobs with a long pipe run, a second-storey or roof-mounted outdoor unit, a new power circuit or several indoor units take longer. The installer confirms the expected timing at the inspection, so the household knows when the power will be switched off and which rooms need clearing.

What kW split system do I need for a bedroom or living room?

The right size depends on the room itself, because ceiling height, window size, sun direction and insulation all change the heat load. Household split systems run from about 2.5 kW to 8 kW, and a small, shaded bedroom usually sits towards the lower end while a large open-plan living area sits towards the upper end. A west-facing room, a raked ceiling or large windows push the size up, and good ceiling insulation brings it down. The installer measures each room at the inspection and states the recommended size on the quote.

Can a split system be installed on an internal wall?

Yes, but it takes more planning than an external wall. The refrigerant pipes, cable and drain have to reach the outdoor unit through the ceiling space, under the floor or inside a wall cavity. The drain usually needs a condensate pump because the water cannot fall to the outside by gravity. The longer pipe run must stay within the manufacturer's limits and adds to the cost, so the installer checks roof or underfloor access before confirming the position.

Can one outdoor unit run two or more split systems?

Yes, a multi-head outdoor unit can run two or more indoor units, and the maximum number depends on the model. Each room keeps its own indoor unit and remote, but the heads share the outdoor unit's total capacity and usually run in the same heating or cooling mode. The manufacturer's pipe length and height limits decide whether the rooms are close enough together. Peak Air Conditioning Glen Waverley prices a multi-head against separate splits in the written quote, so the household can compare both options.

Request A Free Split System Installation Quote

GET A FREE QUOTE