Peak Air Conditioning Glen Waverley designs and installs ducted air conditioning Glen Waverley homes can heat and cool from one system, with a reverse cycle unit hidden in the roof and a ceiling outlet in each room. Each design starts with a room-by-room heat load check, then a duct layout showing where the fan coil, outlets, return air grille and zone dampers will sit. Zoning lets living areas and bedrooms run separately, so the system only conditions the rooms in use. Single-storey homes, double-storey homes and add-on cooling for existing gas ducted heating are all assessed on site. Refrigerant work is carried out under an ARC refrigerant handling licence, and the electrical connection by a licensed electrician. Call to book a site visit and a fixed written quote, with phones answered from 6am to 10pm, seven days.
GET A FREE QUOTE
Air conditioning work in Glen Waverley draws on three licensed trades: refrigerant handling, electrical connection and, for gas heating, gasfitting. Peak Air Conditioning Glen Waverley is based in the suburb, so a job off Kingsway, in a Legend Park Estate house or in a new townhouse near the station is a local trip rather than a drive across Melbourne. Two things decide whether a new or repaired system performs: who handles the work, and how the system is sized for the rooms it serves.
Peak Air Conditioning Glen Waverley
Ducted air conditioning in Glen Waverley is a single system for the whole house: one indoor fan coil hidden in the roof, one outdoor unit outside, and a network of insulated ducts carrying conditioned air to a vent in each room. Only the ceiling outlets, one return air grille and a wall controller are visible inside the home.
A ducted reverse cycle system is a heat pump. In summer it pulls heat out of the house and releases it outdoors; in winter the refrigerant flow reverses, so it draws heat from the outside air and delivers it through the same ceiling vents. One system therefore replaces both a cooler and a heater, and it runs on electricity alone, which matters to households planning to move off gas. The reverse cycle air conditioning page explains the heat pump principle in more detail for wall splits as well as ducted units.
A single-storey home is the simplest case, because the roof space sits directly above every room and the ducts can drop straight to each ceiling. Much of Glen Waverley's housing dates from the 1950s to 1970s, built on large blocks of typically around 800 m2, including the Legend Park Estate opened in 1971, and the installer checks whether each older roof has the height and access this layout needs. A double-storey home, including many of the townhouses now built on subdivided blocks, is harder: the upper roof serves the top floor, while the ground floor needs ducts run through bulkheads, wall cavities or floor voids, or a second ducted system with its own outdoor unit.
Many Glen Waverley homes already have a gas ducted heater, and add-on cooling fits a cooling coil to that heater's supply plenum and pairs it with an outdoor unit, so summer cooling travels through the existing ductwork. It can cost less than a full reverse cycle system, but the gas heater stays in place and keeps burning gas each winter. The existing ducts also have to suit cooling: older heating ducts are often uninsulated or too small for the airflow, and floor outlets are less effective for cooling than ceiling outlets because cool air sinks, so the installer checks the ductwork before recommending add-on cooling over a full replacement.


Peak Air Conditioning Glen Waverley
A ducted job is designed on paper before anything goes into the roof. The design fixes the system capacity, where the fan coil sits, the duct sizes and the outlet positions, and each decision affects how evenly the rooms heat and cool.
The installer measures every room to be conditioned and records ceiling height, window area and which way the glass faces, the ceiling and wall insulation, and how each room is used. A west-facing living room with large windows gains far more afternoon heat than a south-facing bedroom of the same size, so it needs more airflow. Those room loads are added up, with an allowance for zones that will not all run at once, to give the system capacity in kW. An undersized system struggles on the hottest days, and an oversized one costs more to buy and short-cycles.
The indoor fan coil is the largest component and usually sits in the roof space near the middle of the house, so duct runs to the far rooms stay short and balanced. It needs a solid platform across the ceiling joists, enough clearance to remove its panels for servicing, and a safe walkway from the manhole. Condensate from cooling drains by gravity to the outside, with a safe tray under the unit where the manufacturer specifies one. Where the roof pitch is low, a slimline indoor unit or a different position is chosen at the design stage.
Flexible insulated ducts run from the fan coil to each room, sized so the airflow reaches the far outlets without excess noise at the near ones. Each room gets a round or linear ceiling outlet positioned to spread air across the space rather than onto a bed or couch. A large return air grille, usually in a hallway ceiling, draws air back to the fan coil through a filter, and that filter is the part householders clean between services. A return grille that is too small makes the whole system louder and less efficient.
The outdoor unit is larger than a wall split's, so it needs a level slab or mounting feet, clear airflow on all sides and a position away from bedroom windows and the neighbour's fence line. Insulated copper refrigerant lines and the control cable connect it to the fan coil through the roof or wall. Commissioning covers a nitrogen leak test, evacuation of the lines, release of refrigerant, then a check of operating pressures, supply air temperature at each outlet and every zone opening and closing in both heating and cooling mode.
Peak Air Conditioning Glen Waverley
Peak Air Conditioning Glen Waverley sets out the licences, the design and the price in writing before any work starts, so the household knows what is being installed and why.
Australian rules require any person who installs, commissions or services refrigeration and air conditioning equipment to hold a refrigerant handling licence issued through ARC, known as ARCtick. A ducted outdoor unit also needs its own circuit and isolator, and in Victoria that electrical work is done by a licensed electrician, who must give the customer a copy of the Certificate of Electrical Safety for it (Energy Safe Victoria). Householders can ask to see both before work starts. Keeping these records also helps when a manufacturer warranty claim is made, as the warranty applies when the system is installed to the manufacturer's requirements.
After the roof inspection, the quote is based on a drawn duct layout showing where the fan coil, each outlet, the return air grille, the zone dampers and the outdoor unit will go. The household can see which rooms share a zone and ask for changes before signing, rather than finding out on installation day. The written quote then lists the system model and capacity, the number of outlets and zones, the controller, electrical work and any removal of an old heater. The price is held unless the agreed scope changes.
Phones are answered from 6am to 10pm, seven days a week, and site visits can be booked inside those hours, including early mornings, evenings and weekends. A ducted quote needs someone home while the installer measures the rooms and checks the roof space, so out-of-hours visits suit households where both adults work. Same-day visits are offered where possible. For homes near Kingsway or The Glen on Springvale Road, an evening visit avoids taking a day off to wait at home.


Peak Air Conditioning Glen Waverley
Ducted air conditioning cost depends far more on the house than on the brand. Melbourne cost guides put a standard ducted system for a three-bedroom home, or a single-storey four-bedroom with good roof access, at around $8,400 to $14,700, with a typical job near $11,550 (whatsthedamage.com.au, Melbourne, updated November 2026). These are indicative installed figures, not a set price, and the actual cost comes in a written quote after inspection.
A three-bedroom single-storey home with clear roof space is the most common ducted installation and the cheapest per room. A second Melbourne guide puts a typical three-to-four-bedroom outcome at around $8,000 to $14,000 installed (QuickAir, Melbourne, September 2026), close to the whatsthedamage.com.au range above. The spread inside those ranges comes from system capacity, the number of outlets, the brand and model, and whether an old gas heater has to be removed first.
Larger homes need more capacity, more outlets and longer duct runs. For larger four-bedroom homes and up, two-storey homes or systems zoned room by room, the whatsthedamage.com.au Melbourne guide moves to around $12,600 to $23,100, with a typical job near $16,800. A five-bedroom double-storey home usually sits in that upper band, and QuickAir puts large or multi-storey homes at around $10,000 to $25,000 and up. Where the ground floor needs a second system, the price includes a second outdoor unit and fan coil.
Each zone adds a motorised damper in the ductwork and a channel on the zone controller. Mitsubishi Electric's zone controller, for example, can create up to 4 or 8 separate zones (mitsubishielectric.com.au), so a 4-zone system fits the smaller configuration, while a 5 or 6-zone design moves to the 8-zone controller with spare channels. A larger zone count can also call for a bigger return air path or a bypass so the fan is not choked when most zones are closed, which is priced into the quote.
A low roof pitch, a tiled roof with little crawl space, raked ceilings or no internal manhole all slow the job and add labour. In older Glen Waverley homes, the existing ducts from a 1970s or 1980s gas heater are often worn, uninsulated or undersized for cooling. As a reference point for that work, the whatsthedamage.com.au Melbourne guide puts whole-house ductwork replacement for ducted heating at around $2,000 to $6,300 with new insulated flexible ducts. The installer checks whether any old duct can stay before pricing new runs.
Peak Air Conditioning Glen Waverley
Ducted evaporative cooling is the other whole-house option. It costs less to buy, with the whatsthedamage.com.au Melbourne guide putting a whole-house evaporative system at around $2,950 to $7,350 supplied and installed, but it works in a different way and only cools.
An evaporative cooler draws outside air through wet pads, and the water that evaporates lowers the air temperature before a fan pushes it through the ducts. That works well when the outside air is dry, but on muggy days the air cannot take up much more moisture, so the cooling effect drops and the house can feel damp. A reverse cycle system cools by refrigeration and also pulls moisture out of the air as it runs, so it keeps working when the air is humid and the rooms feel drier.
An evaporative cooler has no heating function, so a home with one still needs a separate heater, usually gas ducted heating through its own floor or ceiling ducts. A ducted reverse cycle system heats through the same outlets it cools through. For homes keeping their gas heater, the ducted heating page covers gas ducted heater installation and replacement. Electric ducted heating by reverse cycle is the option that removes gas from the home's heating altogether, which is why it appears under the Victorian Energy Upgrades program.
An evaporative cooler uses mainly fan power, but it consumes water and its pads need replacing every two to five seasons, depending on water quality (The Quote Yard, Victoria, 2026). It also needs windows or doors open so the moist air can escape. A reverse cycle system runs with the house closed, which keeps out dust and street noise, and uses electricity rather than water. Existing evaporative units still need seasonal care, covered on the evaporative cooler service and repairs page.


Peak Air Conditioning Glen Waverley
Zoning is what stops a ducted system heating or cooling the whole house when only part of it is in use. It is set at the design stage, because the zone layout decides where the dampers go in the ductwork.
A motorised damper is a small motor-driven blade fitted inside a duct branch. When a zone is switched off, its damper closes and that branch stops receiving air, so the system's output goes only to the open zones. Each zone can cover one room or several rooms that are used together, served by the same branch. Inverter systems can then reduce their output to suit the smaller area, which is how zoning saves energy rather than just redirecting air. Dampers are checked at each service because a stuck blade leaves a zone permanently on or off.
The most common split puts the kitchen, dining and living rooms in one zone and the bedrooms in another, so the living areas run during the day and the bedrooms at night. Larger homes add a zone for a study, a rumpus room, a teenager's retreat or an upstairs floor. Where an older Glen Waverley home has been extended with a new family room at the back, that extension can be given its own zone, because it may face a different direction and gain heat differently from the original rooms.
A wall controller sets the mode, temperature and which zones are open, and many systems add a phone app. Mitsubishi Electric, for example, notes that its zone control is compatible with its Wi-Fi module, which is installed as an additional adaptor (mitsubishielectric.com.au), and app features differ between brands and models. Room temperature sensors let a zone hold its own setpoint rather than relying on the reading at the main controller in the hallway. That suits a sunny front room and a shaded rear bedroom on the same system.
Peak Air Conditioning Glen Waverley
The best ducted reverse cycle air conditioner for a home is the one sized and zoned to it. Once that is set, brand and model decide how the system fits the roof, how it is controlled and how efficiently it runs.
The four brands differ in useful ways. ActronAir is an Australian brand whose ducted range is designed for Australian homes and conditions (actronair.com.au). Mitsubishi Electric's PEA-M-HAA ducted range uses two-piece indoor units, which the maker describes as ideal for existing homes, because each piece is easier to lift through a manhole into a tight roof (mitsubishielectric.com.au). Daikin and Fujitsu ducted models are quoted on the same basis, with each model's capacity range, indoor unit size and zone controller options compared against the roof space and the zoning plan. The installer quotes the brand that fits the roof and zoning plan.
Efficiency in a ducted system comes from three things: an inverter compressor that slows down once the house reaches temperature, zoning that shrinks the area being conditioned, and well-insulated, well-sealed ducts that do not lose heat in the roof. Correct sizing matters as much as the model, because an oversized unit cycles on and off. The Victorian Energy Upgrades program only discounts products that are approved under the program and are high-efficiency reverse cycle air conditioners, and it lists bill savings of up to $1,140 a year for replacing a ducted gas heater with one (energy.vic.gov.au, updated October 2026).
Reviews are most useful when they describe the installation, such as noise at the outlets, uneven rooms or drainage problems, because these usually trace back to design rather than the brand. Warranty length and terms vary by manufacturer and model, so it pays to read what is covered, for how long, and whether parts and labour are both included. The manufacturer warranty applies when the system is installed to the manufacturer's requirements, and warranty terms often set out servicing requirements, so it is worth checking them and booking regular care through air conditioning service. For a Victorian Energy Upgrades discount, the product must also carry a minimum 5-year warranty.


Call or send a booking request between 6am and 10pm, seven days, describing the system, the rooms involved and the fault or job needed.

The technician inspects the house or the fault, checks sizing, access and wiring, then gives a written quote before any work or part is ordered.

Licensed technicians install or repair the system, test it in heating and cooling modes, explain the controls and leave the required compliance certificates.
The whatsthedamage.com.au Melbourne guide puts a standard ducted system at around $8,400 to $14,700 for a single-storey four-bedroom home with good roof access, and around $12,600 to $23,100 for larger four-bedroom, two-storey or room-by-room zoned homes (November 2026). Capacity, outlet count, zones, roof access and old heater removal set where a home falls in that range. Replacing a ducted gas heater with an eligible reverse cycle system may attract a Victorian Energy Upgrades discount, which the program lists at up to $5,530. A written quote follows an inspection.
It depends on how many rooms are heated or cooled at once. A split system only uses power in the room it serves, so one or two splits in the rooms in use usually cost less to run than a whole-house system. A zoned ducted system narrows the gap by closing off rooms that are empty, and an inverter unit then reduces its output. When most of the house needs conditioning at the same time, the comparison depends on the models' efficiency ratings, the duct insulation and how the zones are used, so it is worked through at the quote.
Ducted air conditioning is a whole-house system with one indoor unit hidden in the roof space and one outdoor unit outside. Insulated ducts carry heated or cooled air from the indoor unit to a ceiling outlet in each room, and a return air grille draws air back. A reverse cycle ducted system both heats and cools, and zoning lets parts of the house be switched off. Only the outlets, the grille and the controller are visible inside.
A ducted installation usually runs over more than one day, because it involves the roof space, every room's ceiling, the outdoor unit and an electrical circuit. A single-storey home with clear roof access is quicker than a double-storey home or one where old gas heater ducts are removed first. Commissioning and checking each zone come at the end. The installer gives the expected timing with the written quote.
Most homes need at least two zones, one for living areas and one for bedrooms, and larger homes add zones for a study, rumpus room or upstairs floor. Rooms used at the same times and facing the same direction can share a zone. Mitsubishi Electric's zone controller, for example, comes in 4-zone and 8-zone configurations, so a 5 or 6-zone design uses the larger one. Peak Air Conditioning Glen Waverley marks the zones on the duct layout before quoting, so the household can adjust them.
The right size comes from a heat load calculation for each room, not a single figure for the whole house. Floor area, ceiling height, window size and orientation, insulation and how the rooms are used all change the capacity needed. The installer also allows for zones that will not all run together. An undersized system struggles on the hottest and coldest days, while an oversized one costs more and cycles on and off, so the recommended kW size is stated on the quote after the room-by-room measure.
GET A FREE QUOTE
BUSINESS
SERVICES
OPERATING HOURS
Sun: 6:00am - 10:00pm
Mon: 6:00am - 10:00pm
Tue: 6:00am - 10:00pm
Wed: 6:00am - 10:00pm
Thu: 6:00am - 10:00pm
Fri: 6:00am - 10:00pm
Sat: 6:00am - 10:00pm