Peak Air Conditioning Glen Waverley provides air conditioning repair Glen Waverley households can book when a split system or ducted unit stops cooling, stops heating, leaks water, ices up or trips the power. The technician reads the error code, tests the capacitors, fan motors, sensors and circuit board, and checks the airflow, coil and condensate drain before naming the fault. If refrigerant is low, the leak is found and sealed before the system is regassed, because gas added to a leaking system escapes through the same leak. Refrigerant work is carried out under an ARC refrigerant handling licence. Daikin, Mitsubishi Electric, Fujitsu and Panasonic systems are among the brands repaired. A written quote follows once the fault is found, and repair bookings are taken from 6am to 10pm, seven days, with same-day visits where possible. Call to book a repair.
GET A FREE QUOTE
Air conditioning work in Glen Waverley draws on three licensed trades: refrigerant handling, electrical connection and, for gas heating, gasfitting. Peak Air Conditioning Glen Waverley is based in the suburb, so a job off Kingsway, in a Legend Park Estate house or in a new townhouse near the station is a local trip rather than a drive across Melbourne. Two things decide whether a new or repaired system performs: who handles the work, and how the system is sized for the rooms it serves.
Peak Air Conditioning Glen Waverley
Glen Waverley's housing runs from 1950s to 1970s homes on large blocks, many with split systems added room by room over the years, to newer townhouses built where older houses have been subdivided. The repairs on this page cover refrigerated air conditioners, both split and ducted. Evaporative coolers run on water rather than refrigerant, so their faults are covered on the evaporative cooler service and repairs page.
A wall-mounted split sits high on the wall to throw air across the room, while a floor console sits low and, in Daikin's description, warms the ground more effectively because it is mounted lower. Both share the same core parts: an indoor coil and fan, an outdoor compressor and condenser fan, refrigerant pipework between the two, and a control board. Common split system repairs include a failed fan capacitor, a blocked condensate drain, a faulty room temperature sensor and a refrigerant leak at a flare joint. On a floor console, the air intake at the base is also checked for blockage by furniture, rugs or dust.
A ducted reverse cycle system hides its fan coil in the roof space or under the floor, with flexible ducts running to ceiling outlets and a return air grille in the hallway. Faults can sit in the fan coil itself, in a zone damper motor stuck open or shut, in a split or disconnected duct, or in the wall controller and its wiring. When one room gets no air while the others work, the zone motor and the duct to that outlet are the first suspects; when the whole house is affected, attention moves to the fan coil, the outdoor unit and the controller. Mitsubishi Electric states that its zone controller can create up to 4 or 8 separate zones, and each zone adds another motor and another run of wiring that can fail.
Daikin, Mitsubishi Electric, Fujitsu and Panasonic split and ducted systems are repaired, along with other makes found in local homes. Each brand uses its own error code list, its own control board layout and its own replacement parts, so the model number on the rating plate is recorded before any part is ordered. Mitsubishi Electric's current MSZ-AP wall series runs on R32 refrigerant, while older units in many homes run on R410A or R22. For parts, the age of the model matters more than the badge: a current model is far easier to source parts for than one discontinued years ago.


Peak Air Conditioning Glen Waverley
Most repair calls start with a symptom rather than a fault code. Each symptom below points to a short list of likely causes, and the fix depends on which cause the tests confirm.
An air conditioner that runs but blows room-temperature or warm air in cooling mode usually has one of four problems: a clogged filter or dirty coil choking the airflow, an outdoor fan or compressor that is not starting, a failed capacitor, or a low refrigerant charge from a leak. The winter version of this fault, a reverse cycle unit blowing cold air in heat mode, can point to a stuck reversing valve, a defrost sensor fault or the same refrigerant leak. Mode settings and filters are checked first, then the outdoor unit, before refrigerant gauges are connected. Cleaning a neglected system is routine air conditioning service work rather than a repair.
Water dripping from a wall unit, or a ceiling stain under a ducted fan coil, usually traces back to the condensate. A cooling coil pulls moisture out of the air, and that water has to drain away through a hose or a condensate pump. A blocked drain line, a cracked drip tray, a failed pump on a ducted system or an indoor unit hung off level lets it overflow instead. Ice that has built up on the coil can also melt at once and spill past the tray. Clearing and flushing the drain fixes many leaks, while a cracked tray or a failed pump is replaced.
Ice on the copper pipes at the outdoor unit, or frost across the indoor coil in cooling mode, means the coil is running colder than it should. Low airflow is one cause: a blocked filter, a slow indoor fan or a closed-off ducted zone starves the coil of warm air. Low refrigerant is the other: when the charge drops, pressure in the coil falls and its surface freezes. Switching the unit to fan only lets the ice melt while waiting for a technician. The ice is a symptom rather than the fault, so the cause behind it still has to be found.
Rattling usually comes from a loose panel, a mounting bracket or a twig caught in a fan. Buzzing at the outdoor unit can mean a failing capacitor or contactor struggling to start the compressor. Grinding or squealing points to worn fan motor bearings or a fan blade rubbing its housing. Each noise is traced to its source with the panels off. A worn motor left running can seize completely, which turns a bearing noise into a motor replacement.
A system that stays dead when switched on may have a tripped circuit breaker, flat remote batteries, a failed control board or a fault in the wiring between the indoor and outdoor units. A unit that trips the safety switch or circuit breaker is a different problem: it points to a short circuit, a failing compressor drawing too much current, or moisture in the wiring. Resetting a breaker once is reasonable, but a unit that trips it again should be left off until it has been tested. Testing inside the unit is work for a licensed technician, not a home fix.
Peak Air Conditioning Glen Waverley
Fault-finding follows a set order so the cause is confirmed before a part is replaced. Replacing the wrong part costs money and leaves the real fault in place.
Modern split and ducted systems run a self-diagnosis and report faults as a code on the wall controller or as a pattern of flashing lights on the indoor unit. The code narrows the fault to an area, such as a temperature sensor, the outdoor unit or communication between the two units, but it rarely names the exact failed part. Codes differ between brands and between model series, so they are read against the manufacturer's service data for that model. Some models also keep a record of past codes, which helps when a fault comes and goes.
With the power isolated, the technician tests the fan and compressor capacitors against their rated capacitance, checks the contactor, measures the resistance of the room and coil temperature sensors, and checks the voltage reaching the indoor and outdoor boards. A capacitor that has drifted out of range can leave a fan or compressor humming without starting. A sensor reading the wrong temperature can make a unit stop early or never reach its set point. A circuit board is condemned only after the parts around it test sound, because it is the dearest of these parts to replace.
Airflow checks start at the filters and the return air grille, then move to the indoor fan speed and, on a ducted system, the air temperature at each outlet. The coil fins are inspected for matted dust and corrosion, and the outdoor condenser is checked for leaves, lint or anything blocking its airflow. The condensate drain is flushed to confirm water runs freely to its outlet. If all of these checks are sound and the system still underperforms, refrigerant pressures are measured with gauges to test for a leak.


Peak Air Conditioning Glen Waverley
Peak Air Conditioning Glen Waverley keeps repair work straightforward: licensed hands on the job, the fault explained in plain terms, and the price in writing before the fix goes ahead.
Under the Australian Refrigeration Council's rules, any person who handles refrigerant or works on refrigeration and air conditioning equipment must hold a refrigerant handling licence, and the technicians hold one. That covers recovering gas, sealing leaks and regassing. Electrical work such as a damaged power supply or a new isolator is carried out by a licensed electrician. Asking to see an ARC licence number before work starts is a fair check to make of any repairer.
Once the tests confirm the fault, the technician explains what has failed and why, then gives a written quote for the part and labour. If the system is old and the repair is costly, the quote sets that out so the repair can be weighed against a replacement. The repair goes ahead only once the quote is accepted. If a part has to be ordered in, the quote says so and gives the expected return visit.
Repair calls are taken from 6am to 10pm, seven days, so a visit can be booked before work, after work or on a weekend. Same-day visits are offered where possible, depending on the day's bookings. For a breakdown that cannot wait or happens outside those hours, the emergency air conditioning repair page explains the after-hours option.
Peak Air Conditioning Glen Waverley
Repair prices depend on the fault, the part and how easy the unit is to reach. The figures below come from published Victorian and Melbourne cost guides. They are indicative only and are not a quote; a written quote follows the diagnosis.
The Quote Yard's 2026 Victorian repair guide prices the attendance and diagnosis fee by Melbourne area and lists Glen Waverley in its south eastern band, at around $130 to $240, and notes that the call-out is usually credited against the repair if it goes ahead. The same guide lists hourly rates of about $110 to $180 with a minimum charge, and a typical south eastern repair total of around $340 to $1,050. Whatsthedamage.com.au puts a minor air conditioning repair in Melbourne at around $160 to $525 per job (November 2026).
The Quote Yard lists fitted prices of around $180 to $400 for a capacitor, $200 to $450 for a contactor, $450 to $900 for a fan motor and $500 to $1,400 for a control board. A reversing valve, the part that switches a reverse cycle unit between heating and cooling, is listed at $700 to $1,500, and a compressor at $1,400 to $2,800. Where a job sits within each range comes down to the brand, the model, the size of the unit and whether the part is in stock or has to be ordered.
The Quote Yard puts a leak repair and regas at around $400 to $900 in Victoria, and whatsthedamage.com.au puts a major repair or regas in Melbourne at $315 to $1,250 per job. Those ranges cover finding the leak, sealing it, evacuating the system and recharging it. Refrigerant type affects the price mainly through supply. R22 imports are limited to a small servicing allowance until 2029, after which R22 systems rely on recycled or reclaimed refrigerant (Australian Refrigeration Council, August 2023), so R22 work is priced once the gas has been sourced. No published guide splits the price of R32 and R410A work, so the written quote names the refrigerant being used.
Ducted repairs often carry more labour than a split repair, because the fan coil sits in the roof space or under the floor and is reached through a manhole, sometimes across ceiling joists with little headroom. On a two-storey home, the outdoor unit may sit on a roof or upper balcony and the fan coil above the top-floor ceiling, which can mean extra access equipment and more time. No published Melbourne guide gives a separate ducted or two-storey surcharge, so access is priced on inspection and shown in the written quote.


Peak Air Conditioning Glen Waverley
When an old system breaks down, the question is whether to fix it or replace it. Three things decide it: the age of the unit and its parts, the repair price against a new unit, and what the old system costs to run.
Daikin states that a split system can last 10 to 15 years or more with regular maintenance. Once a model has been discontinued for some years, its control boards, fan motors and sensors become harder to find, and some are no longer made at all. A system that runs on R22 adds a further limit, because R22 supply for servicing is restricted. The model number on the rating plate shows how old the unit is and whether parts are still available, and that is checked before a repair is quoted.
Weigh the repair quote against what a replacement costs. Whatsthedamage.com.au puts a like-for-like split system changeover with the old unit removed at around $1,575 to $3,150 in Melbourne (November 2026). A low-cost part such as a capacitor on a newer unit is usually worth replacing, while a compressor at $1,400 to $2,800 on an old R22 unit comes close to the cost of a new system. Where replacement makes more sense, air conditioning installation covers sizing and fitting a new system.
An older system that has lost refrigerant or has a dirty coil works harder to deliver the same heating or cooling. Newer models carry the Zoned Energy Rating Label, which rates heating and cooling efficiency from 1 to 10 stars across hot, average and cold climate zones, so a replacement can be compared for Melbourne conditions. For rented homes, the Victorian Energy Upgrades program states that when a space heater in a rental home breaks and cannot be repaired after 1 March 2027, it must be replaced with an efficient reverse cycle air conditioner with an outlet in the main living area. Rental providers should check the current Consumer Affairs Victoria rules for their own lease.
Peak Air Conditioning Glen Waverley
Refrigerant circulates in a sealed loop and is not used up, so a system that is low on gas has a leak somewhere. Regassing without finding that leak simply refills a system that will lose its charge again.
A unit low on refrigerant tends to show several signs together: weaker cooling or heating that gets worse over weeks, ice on the copper pipes or the indoor coil, a hissing or bubbling sound from the pipework, oily residue at a pipe joint, and an outdoor unit that runs for long periods without the room reaching its set temperature. Some models also display a fault code linked to low charge. These signs overlap with airflow faults, so gauges confirm the charge before any gas is added.
Leaks are commonly found at the flare joints where the copper pipes connect to the indoor and outdoor units, at the service valves, or in a coil where corrosion has worn through the tube. An electronic leak detector, bubble solution or a nitrogen pressure test is used to find the point of loss. A flare joint is re-made, a damaged pipe section is replaced, and a leaking coil is assessed for repair or replacement. The system is then pressure tested with nitrogen, evacuated with a vacuum pump to remove air and moisture, and recharged to the weight on the rating plate.
Each air conditioner is designed for one refrigerant, named on its rating plate, and gases are not mixed or swapped without an approved conversion. R32 is the refrigerant in many current split systems, including Mitsubishi Electric's MSZ-AP range, and R410A is found in many systems installed before R32 models became common. R22 is the oldest of the three: the Australian Refrigeration Council notes that Australia largely phased out HCFC imports, including R22, in 2016, and that R22 systems in good working order do not need to be converted and can still be serviced with R22. Converting an R22 system to another refrigerant is allowed only when the substitute is accepted for that use and the work meets the relevant legislation and Australian Standards.


Call or send a booking request between 6am and 10pm, seven days, describing the system, the rooms involved and the fault or job needed.

The technician inspects the house or the fault, checks sizing, access and wiring, then gives a written quote before any work or part is ordered.

Licensed technicians install or repair the system, test it in heating and cooling modes, explain the controls and leave the required compliance certificates.
Check the simple things first: the remote batteries, the mode setting, the circuit breaker and whether the filter is clogged. If the unit still will not run, trips the power, leaks water or smells of burning, switch it off at the isolator and leave it off. Note any error code or flashing light pattern, as it helps narrow down the fault. Then book a licensed technician to diagnose it; Peak Air Conditioning Glen Waverley takes repair calls from 6am to 10pm, seven days.
The Quote Yard's 2026 Victorian guide lists Glen Waverley in its south eastern band, with a call-out and diagnosis fee of around $130 to $240, usually credited against the repair if it proceeds, and says most repairs land between $300 and $900. It lists a fitted capacitor at $180 to $400, a fan motor at $450 to $900 and a control board at $500 to $1,400. These are indicative guide prices, and a written quote is given once the fault is found.
The usual causes are a blocked filter or dirty coil restricting airflow, an outdoor unit that is not starting because of a failed capacitor or fan motor, and low refrigerant from a leak. A wrong mode setting or a closed ducted zone can produce the same symptom. Check the filter and settings first. If the unit still blows warm air, a technician tests the outdoor unit and the refrigerant pressures to confirm the cause.
Signs include cooling or heating that has weakened over time, ice on the copper pipes or indoor coil, a hissing sound at the pipework and a unit that runs for long periods without reaching its set temperature. Because refrigerant runs in a sealed loop, low gas means there is a leak. A licensed technician confirms the charge with gauges, finds and seals the leak, and then regasses the system.
The Quote Yard lists a leak repair and regas in Victoria at around $400 to $900, and whatsthedamage.com.au puts a major repair or regas in Melbourne at $315 to $1,250 per job. The price depends on where the leak is, how much refrigerant is needed and which refrigerant the system uses. R22 systems depend on limited supply, so their price is confirmed once the gas is sourced. A written quote is given after the leak is found.
It depends on the repair price, the age of the unit and whether parts are still available. Daikin states that a split system can last 10 to 15 years or more with regular maintenance, so a minor repair on a unit inside that range is often worth doing. A major part such as a compressor on an old or R22 system can come close to the cost of a new unit, which Melbourne guides put at around $1,575 to $3,150 for a like-for-like split changeover. Peak Air Conditioning Glen Waverley sets both options out in the written quote so the choice is clear.
GET A FREE QUOTE
BUSINESS
SERVICES
OPERATING HOURS
Sun: 6:00am - 10:00pm
Mon: 6:00am - 10:00pm
Tue: 6:00am - 10:00pm
Wed: 6:00am - 10:00pm
Thu: 6:00am - 10:00pm
Fri: 6:00am - 10:00pm
Sat: 6:00am - 10:00pm