Air Conditioning Installation Glen Waverley, Sized to Your Home

Peak Air Conditioning Glen Waverley provides air conditioning installation Glen Waverley wide, from a single wall-mounted split in a bedroom to a zoned ducted reverse cycle system for a whole family home. Every job starts with a room-by-room heat load check, so the capacity in kW suits the space, the windows and the insulation rather than a guess from the showroom floor. The technician then works out where the indoor and outdoor units can sit, how far the refrigerant pipework has to run and whether the switchboard needs a new circuit. Refrigerant work is carried out under an ARC refrigerant handling licence and the electrical connection by a licensed electrician. Call for a fixed written quote after an on-site inspection.

GET A FREE QUOTE

Licensed Air Conditioning Glen Waverley Technicians for Air Conditioning Installation

Air conditioning work in Glen Waverley draws on three licensed trades: refrigerant handling, electrical connection and, for gas heating, gasfitting. Peak Air Conditioning Glen Waverley is based in the suburb, so a job off Kingsway, in a Legend Park Estate house or in a new townhouse near the station is a local trip rather than a drive across Melbourne. Two things decide whether a new or repaired system performs: who handles the work, and how the system is sized for the rooms it serves.

Air Conditioning Installation Glen Waverley: Split, Multi-Head and Ducted Systems

Air conditioning installation in Glen Waverley covers four system types, chosen by the number of rooms and how the house is built.

Wall-Mounted Split Systems for Single Rooms

A wall-mounted split system pairs one indoor head with one outdoor unit and suits a single living room, bedroom or home office, and the split system installation page covers sizes and placement.

Multi-Head Systems Running Several Rooms From One Outdoor Unit

A multi-head system connects two or more indoor heads to one larger outdoor unit. It saves wall and garden space on narrow townhouse blocks, but the shared outdoor unit caps total capacity, so the rooms are sized together.

Ducted Reverse Cycle Systems for the Whole House

A ducted reverse cycle system hides the indoor unit in the roof space and feeds heated or cooled air to every room through ceiling vents. The 1950s to 1970s homes on Glen Waverley's large blocks often have the roof space this needs, and the ducted air conditioning page covers duct layout and zoning design in depth.

Ceiling Cassette and Floor Console Units

A ceiling cassette sits flush in the ceiling and spreads air in several directions, which suits open-plan rooms. A floor console sits low on the wall where high wall space is taken by windows.

Forest Hill Emergency Air Conditioning Repair
Clayton Emergency Air Conditioning Repair

How an Air Conditioner Is Sized and Installed

A good installation follows the same four steps every time, and skipping one is a common reason a new system struggles.

Heat Load Calculation Room by Room

The technician measures each room and notes the ceiling height, window size and orientation, insulation and the number of people who use the space. A west-facing lounge needs more capacity than a shaded bedroom of the same size, and the result is a kW figure for each room.

Indoor and Outdoor Unit Placement

The indoor head goes where the air can reach the whole room without blowing straight onto a bed or couch. The outdoor unit needs clear airflow, a solid base or wall bracket, and a spot that keeps its noise away from bedroom windows and the neighbouring house.

Refrigerant Pipework, Pressure Testing and Vacuum

Insulated copper pipes are run between the units, flared and joined, then the system is pressure tested with nitrogen to find any leak, and a vacuum pump draws out air and moisture before the refrigerant is released. A rushed vacuum leaves moisture that shortens compressor life.

Electrical Connection and Commissioning

The unit is wired to its own circuit and isolator by a licensed electrician. Commissioning then checks the operating pressures, airflow, drainage and both heating and cooling modes, and the owner is shown how to clean the filters.

Why Choose Peak Air Conditioning Glen Waverley

Peak Air Conditioning Glen Waverley keeps the process plain: licensed trades, a written price and hours that suit working households.

Licensed Refrigerant and Electrical Work

Every person who installs or commissions refrigeration and air conditioning equipment in Australia must hold an ARC refrigerant handling licence, and the technician holds one. The final electrical connection is carried out by a licensed electrician, so the circuit, isolator and switchboard work meet the wiring rules.

Fixed Written Quotes Before Work Starts

After the on-site inspection, the business provides a written quote that lists the unit, the pipe run, any brackets, the electrical work and removal of an old system. The price is fixed before work starts, so there is no surprise charge on the day.

Open 6am to 10pm, Seven Days

The phones are answered from 6am to 10pm, seven days a week, so a quote visit can be booked before or after work. Same-day inspections are offered where possible.

Burwood East Emergency Air Conditioning Repair
Clayton Emergency Air Conditioning Repair

What Air Conditioning Installation Costs in Glen Waverley

Melbourne cost guides put a supplied and installed split system at around $1,250 to $2,625 for a 2.5 kW unit, $1,475 to $2,950 for 3.5 kW and $2,300 to $4,725 for 7 kW (whatsthedamage.com.au, Melbourne, November 2026). A two-head multi-split sits at around $4,200 to $7,900, and a standard ducted system for a three-bedroom home at around $8,400 to $14,700. These figures are indicative, and a written quote follows inspection.

System Type and Capacity in kW

Larger kW units cost more, and a zoned ducted system for a larger or two-storey home runs to around $12,600 to $23,100 in the same Melbourne guide.

Back-to-Back Versus Long Pipe Runs

A back-to-back install puts the outdoor unit directly behind the indoor head on the same wall, which keeps labour and pipe to a minimum. One Melbourne installer's calculator puts a 3.5 kW back-to-back job at around $2,100 to $2,600 (Climate Control Solutions, reviewed July 2026), and every extra metre of pipe adds to that.

Roof Space, Wall Brackets and Two-Storey Access

Cramped roof space slows ducted work, and an outdoor unit mounted high on a second-storey wall needs a bracket and safe access, which is common on the townhouses that have replaced older homes on subdivided blocks.

Switchboard and Circuit Upgrades

Older switchboards in 1950s to 1970s homes often have no spare room for a dedicated circuit. The same installer guide allows roughly $450 extra for a new circuit, and an older board may need upgrading before any unit can be connected.

Split System Versus Ducted Air Conditioning

The choice comes down to how many rooms need conditioning and how the household uses them.

Upfront Price and Running Costs

One or two splits cost far less to install than a ducted system, and they only use power in the rooms that are switched on. Ducted costs more upfront but serves the whole house from one unit. Both are reverse cycle air conditioning, so either can replace gas heating as well as cool in summer.

Zoning and Room-by-Room Control

Splits are zoned by nature: each head has its own remote and setpoint. A ducted system gains the same control through zone motors in the ductwork, so the bedrooms can run at night while the living areas are shut off.

Noise, Looks and Space Taken

A split head is visible on the wall and its outdoor unit takes space beside each room. Ducted puts only slim vents in the ceiling and a single outdoor unit outside, so rooms stay quieter and tidier.

Burwood East Emergency Air Conditioning Repair
Clayton Emergency Air Conditioning Repair

Replacing an Old or Failed Air Conditioner

Many Glen Waverley homes still run systems fitted decades ago. Melbourne cost guides put a like-for-like changeover with the old unit removed at around $1,575 to $3,150 (whatsthedamage.com.au, November 2026).

Removing the Old Unit and Recovering Refrigerant

Refrigerant must never be vented to the air. A licensed technician recovers it into a cylinder for proper disposal, then removes both old units.

When Existing Pipework Can Be Reused

Existing copper pipes can sometimes be reused if they are the right size for the new unit, in good condition and suited to its refrigerant, and if the manufacturer allows it. Pipework from older R22 systems often needs flushing or replacing, so the technician checks it before quoting.

Swapping Gas Heating for Reverse Cycle Under Victorian Energy Upgrades

The Victorian Energy Upgrades program lists discounts of up to $1,610 for replacing a non-ducted gas space heater with an efficient reverse cycle air conditioner, and up to $5,530 for replacing a ducted gas heater (energy.vic.gov.au, updated October 2026). The product must be approved under the program, carry a minimum 5-year warranty and be installed in a property more than 2 years old. Homes keeping gas can still have their heater looked after through ducted heating.

Choosing an Air Conditioner Brand and Energy Rating

Once size and type are settled, brand and efficiency rating decide how well the unit runs.

Daikin, Mitsubishi Electric, Fujitsu and Other Brands

The technician installs the brands most Melbourne homes choose, including Daikin, Mitsubishi Electric, Fujitsu, Panasonic and others. Models differ in wi-fi control, quiet modes and filters, so the recommendation follows the room and budget, not a favourite brand.

Energy Rating Labels and Inverter Technology

The Zoned Energy Rating Label shows separate star ratings for heating and cooling across hot, average and cold climate zones, so buyers can compare units on the zone that matches their home. Almost every modern split uses an inverter compressor, which speeds up and slows down to hold the set temperature instead of switching fully on and off.

Manufacturer Warranty Terms

Warranty length and conditions vary by brand and model. The manufacturer warranty applies when the unit is installed to the manufacturer's requirements, and every install follows that standard. Ongoing care is covered on the air conditioning service page.

Burwood East Emergency Air Conditioning Repair

TESTIMONIALS

What Our Air Conditioning Installation Customers Say About Us

The Process

3 Step Process For Your Air Conditioning Installation Needs

Booking

Call or send a booking request between 6am and 10pm, seven days, describing the system, the rooms involved and the fault or job needed.

Written Quote

The technician inspects the house or the fault, checks sizing, access and wiring, then gives a written quote before any work or part is ordered.

Job Completed

Licensed technicians install or repair the system, test it in heating and cooling modes, explain the controls and leave the required compliance certificates.

FREQUENTLY ASKED QUESTIONS

Air Conditioning Installation In

Everything you need to know about our Air Conditioning Installation In

How much does it cost to have an air conditioning unit installed in your house?

Melbourne cost guides put a supplied and installed split system at around $1,250 to $2,625 for 2.5 kW and $1,475 to $2,950 for 3.5 kW, and a standard ducted system for a three-bedroom home at around $8,400 to $14,700 (whatsthedamage.com.au, November 2026). Size, pipe run, access and switchboard work set the final price. A written quote is given after an on-site inspection.

How long does air conditioning installation take?

A single back-to-back split system is usually finished within a day. A ducted system involves roof work, ductwork and several vents, so it normally runs over more than one day. The technician gives a time estimate with the written quote.

What size air conditioner do I need for my room?

Ceiling height, window size, which way the room faces, insulation and how many people use it all change the capacity needed. An undersized unit runs flat out, while an oversized one cycles on and off. The technician measures the room before recommending a unit.

Do air conditioning installers in Victoria need a licence?

Yes. Anyone who installs, commissions or services refrigeration and air conditioning equipment in Australia must hold a refrigerant handling licence issued through ARC (ARCtick). The electrical connection must be done by a licensed electrician. Peak Air Conditioning Glen Waverley uses licensed technicians for both parts of the job.

Which are the best air conditioner brands in Australia?

Daikin, Mitsubishi Electric, Fujitsu and Panasonic are among the brands most widely installed in Australian homes. No single brand is best for every room, as features and efficiency vary by model. Compare the Zoned Energy Rating Label for heating and cooling, the warranty terms and the size match.

Can I get a discount on a new air conditioner in Victoria?

Possibly, if the new system replaces gas heating. The Victorian Energy Upgrades program lists discounts of up to $1,610 for replacing a non-ducted gas space heater and up to $5,530 for replacing a ducted gas heater with an efficient reverse cycle air conditioner. The product must be program-approved with a minimum 5-year warranty, and the property must be more than 2 years old. Eligibility is listed on energy.vic.gov.au.

air conditioning Burwood East

Request A Free Air Conditioning Installation Quote

GET A FREE QUOTE